This fully automatic metal cutting machine fits right into real workshop scenarios: In steel processing yards, it cuts batches of steel bars for construction sites without stopping; in auto parts workshops, it cuts small, precise metal pieces for car frames; in hardware manufacturing plants, it handles high-volume cutting of angle steel and square tubes for furniture and tools. It's especially useful for workshops that run 2-shift operations-you can set it up before the night shift, and it will keep cutting while workers do other tasks, no need to stay by the machine.
A small heads-up from my experience: It needs a stable power supply. Also, the automatic feeding system works best with straight, smooth materials;if your steel bars are bent (from transport), you'll need to straighten them first, otherwise they might get stuck in the feeding rail. And don't forget to clean the metal chips off the workbench and feeding rail after each shift-they build up and can slow down the machine over time.
It's ideal for workshop owners who are tired of wasting material, overworking their staff, and dealing with inconsistent cuts. This fully automatic metal cutting machine isn't just a tool-it's a time-saver that lets you take on more orders (my Spanish client added 3 new clients after switching) and boost profits without adding extra workers. It fits right into your daily workflow, no complicated setup, just reliable, consistent cutting day in and day out.
| MODEL | XG-120 | |||
| Cutting Capacity | Bar | ● | mm | 20-120 |
| Angle | ■ | mm | 20-85 | |
| Round tube | ○ | mm | 20-120 | |
| Square tube | □ | mm | 20-85 | |
| Head spindle | Using TCT super hardcircular saw blade | mm | Φ380t2.6 | |
| Spindle motor | kw | 11/15 | ||
| Spindle speed | rpm | 20-120 | ||
| Cut off feed mode | AC servo motor + ball screw l swing feedAC | |||
| Main clamp mode | Hydraulic l one set for vertical and one set for horizontal clamping | |||
| Saw blade debris removal device | Passive round wire brush I Active round wire brush (optional) | |||
| Gear Backlash CompensationDevice | Through shaft magnetic powder brake | |||
| Feeding clamp | Feeding driving mode | AC servo motor + ball screw I swing feedAC | ||
| Feeding clamp mode | Hydraulic I horizontal clamping | |||
| Material front end removal length | mm | 10~101 (no cutting head is optional) | ||
| Rear end residuelength | mm | 75+α | ||
| α is not enough to cut a workpieceα | ||||
| Single feeding length | mm | 10-800 | ||
| Feeding device | Allowable feedinglength | mm | 3000-6002 | |
| Feeding mode | Pre arranged hydraulic lifting | |||
| Hydraulic drive | Type of hydraulic pump | Variable displacement piston pump | ||
| Hydraulic drive motor | kw | 3.75(4P) | ||
| Rated pressure of hydraulic system | Mpa | 9 | ||
| Hydraulic oil capacity | L | 110 | ||
| Size and weight | Weight(machine + rack) | kg | 6000 | |
| size | mm | 7700×3200×2250 | ||
| Other standarde quipment |
Anti vibration device for saw blade deflection | Tungsten carbide parallel block | ||
| Distributor | Pneumatic reciprocating | |||
| Automatic centralized grease lubrication system | Timing and quantitative forced oil supply | |||
| MQL tool micro lubrication SystemMQL | Quasi dry intermittent oil feeding | |||
| Chip conveyor | Chain plate l continuous or intermittent operation | |||
| Work lights | Led l waterproof and dustproof | |||
| Electric control box heat exchanger | Closed high efficiency heat exchange system | |||
| optionaldevices | Centrifugal oil mist recovery machine | Multistage filtration, energy saving and environmental protection | ||
| Cluster feeder | Whole bundle feeding, long material cutting preferred | |||
| Third clamp | Scrap length 22+α (α is not enough to cut a workpiece) | |||
| wire brush | Active chip removal | |||
| Long material receiving device(discharging device) | Flexible selection of various ways, can be equipped with robot discharge code material | |||
FAQ
Q: Can the fully automatic metal cutting machine handle different sizes of metal materials?
A: Yes, it can. It supports round bars, square bars, and irregular metal pieces within the maximum cutting range (350mm for round bars, 350×350mm for square materials). You just need to adjust the clamping device and cutting speed according to the size and hardness of the material, no need to replace any parts.
Q: Does the metal cutting machine require professional operators?
A: No, it doesn't. The control panel is simple and easy to understand, with clear labels for each button. We will provide a detailed operation manual and simple training guidance. Generally, workers can master basic operation within 1-2 days, even if they have no prior experience with cutting machines.
Q: How to maintain the metal cutting machine to ensure its long-term stable operation?
A: Daily maintenance is simple. First, clean the metal chips on the workbench and feeding rail after each use to avoid jams. Second, check the lubrication of the blade and guide rail regularly, and add lubricating oil in time. Third, check the power supply and wiring to ensure there is no loose contact. Doing these can effectively extend the service life of the machine.
Q: Can the metal cutting machine be customized according to our specific cutting needs?
A: Yes, it can. If your workshop mainly processes special-sized metal materials or has specific requirements for cutting precision, we can adjust the machine's cutting range, control system, and feeding speed. Many of our clients have customized the machine according to their production needs, and the effect is very good.
Hot Tags: fully automatic metal cutting machine, China fully automatic metal cutting machine manufacturers, suppliers, factory, High Precision Hydraulic Press, Steam Type Cooling Fan Hydraulic Press, , Two Beam And Four Column Hydraulic Press, FRP Manhole And Frame Press Machine, 200T Servo Hydraulic Press
